Can the Aluminum Alloy of the Can Replace the Aluminum Alloy of the Aluminum Sheet?

 As a Perforated Metal Sheets Factory, share with you.

As we all know, the curtain wall aluminum veneer is made of aluminum alloy. The Coca-Cola cans are also made of aluminum alloy. However, most people think that aluminum alloys are the same, and there is no difference. In fact, they are different. The aluminum alloy used in cans cannot meet the basic mechanical properties of curtain wall aluminum veneers.

3104 aluminum alloy is used for the can body, 5052 aluminum alloy is used for the lid and pull ring of the can; and the aluminum alloy used for the aluminum veneer of the curtain wall is 1100 and 3003 aluminum alloy. Because of the different models of aluminum alloys, their mechanical properties are also different. For example, the ultimate tensile strength of 6061 aluminum alloy is 124MPa, the tensile yield strength is 55.2MPa, the elastic modulus is 68.9GPa, and the bending ultimate strength is 228MPa. It is usually used in aviation and shipbuilding. The mechanical performance requirements of curtain wall aluminum veneer do not need to meet the aviation aluminum alloy standards, but the aluminum alloy used for cans obviously cannot meet its basic mechanical performance requirements. In order to make huge profits, some aluminum manufacturers use shoddy aluminum to reproduce the recycled aluminum scrap into aluminum coils and sell them to aluminum veneer manufacturers. The curtain wall aluminum veneer formed by using this low-grade aluminum alloy is not distinguishable from the surface of the aluminum veneer, but after a long time of use, problems of corrosion and structural strength reduction will occur. The aluminum alloy used in the curtain wall aluminum veneer should strictly comply with the relevant quality standards of the construction industry promulgated by my country.

Of course, the vigorous development of curtain wall aluminum veneer is inseparable from the continuous development and innovation of aluminum alloy smelting technology. It is also expected that aluminum alloys with better mechanical properties will be used on building curtain walls in the future.

Our company also has Expanded Metal Mesh on sale, welcome to contact us.



评论

发表评论

此博客中的热门博文

Repair the Surface of Aluminum Composite Panel

图片
Aluminum-plastic composite panel is a product that is often used in life. This type of product is used in many places. For many people, it has a very good effect. It is also often used in the home improvement industry, but because of the workmanship. There will be some differences between different types of plates, resulting in products that don’t look very good. What should we do to deal with this situation? First of all, we must understand what causes the color difference of the plates, and work with   Perforated Metal  Sheets Factory ! 1. Reasons for raw materials. The supplier is different. The difference of suppliers has a great influence on the control of color production. Almost all the raw materials of the paint factory come from different places. If different suppliers are required to prepare the same color, there are actually differences in raw materials. Sometimes the same supplier also has the problem of differences in raw materials of different habits. 2. Equipment reasons
阅读全文

the Cause of the Uneven Surface of the Aluminum Panel

图片
The application of aluminum veneer is more and more widespread, and the uneven surface of the aluminum sheet is one of the problems that everyone often encounters. So what is the cause of the uneven surface of the aluminum veneer? In fact, there are many reasons, such as: aluminum sheet Extrusion die setting problems, support pad problems, etc.   Perforated Metal Sheets Factory   will tell you the specific reasons for the uneven surface of the aluminum veneer: (1) The length ratio of the working belt of the aluminum extrusion die or the design of the cavity size is wrong and the flow rate ratio is seriously out of adjustment. (2) The working of aluminum Panel extrusion die has obstruction angle and flow promotion angle. (3) The gap between the upper and lower molds of the aluminum panel extrusion die is relatively poor. (4) The working belts of the upper and lower dies of the aluminum panel extrusion die are not parallel, and there are horns. (5) The upper die resistance (division) flo
阅读全文